| |
||||||||||||||||||||||||||||||||||||||||||||||||
 |
A heavy duty high performance trailed wrapper, capable of wrapping a bale on the turntable while carrying another on the load arm. The machine is fitted with a 750mm wide pre-stretch unit and a hydraulic cut and tie system as standard. The pre-stretch unit consists of aluminium rollers geared to each other with two heavy duty steel gears, giving a film stretch of 70%. |
The turntable is powered by a hydraulic motor, and consists of two chequer plate rollers, thus eliminating the need for belts. The very low hydraulic oil flow requirement of 15 L/m is well within the range of even the smallest tractor, while the turntable speed is controlled by the use of a hydraulic flow divider.
When wrapped the bale is offloaded onto a hydraulic tail mat, which eliminates impact damage on contact with the ground.
The wrapper is fitted with a bale wrap monitor which is programmed to operate a warning buzzer when the correct number of film layers have been applied to the bale. It also shows the number of bales wrapped, with an end of season total.
Wide flotation tyres are used to cater for even the softest ground conditions.
Superwrap (Linkage Mounted)
 |
This Unique design of wrapper, while retaining all the features of it's trailed counterpart, has shown distinct advantages on wet land, hills and places with difficult access. being linkage mounted it is highly manouverable and is built to withstand the extreme pressures associated with continuous contractor use. It has an extremely low drop-off height of approximately 12 inches. |
A hydraulic cut and tie system and bale wrap monitor are fitted as standard. The typical 50 H.P. tractor is quite capable of operating it with ease, and can totally wrap the bale in approximately 30 seconds.
Heavy duty bearings are used throughout with grease points clearly marked to facilitate many years of trouble free use.
Technical Data |
||
| Trailed Superwrap | Linkage Superwrap | |
| Transport Length. | 3.7m | 1.9m |
| Transport Width. | 2.25m | 1.3m |
| Weight | 1120kg | 660kg |
| Linkage | - | Cat. 1 or 2 |
| Hydraulic Flow Pressure | 3.25 gpm (14.8 L/m) 200 psi (140 bar) | 3.25 gpm (14.8 L/m) 200 psi (140 bar) |
| Bale size (Meters) | 1.2 x 1.2 | 1.2 x 1.2 |
| Max. Bale Weight | 1000kg | 1000kg |
| Film Layers | 2+2 x 50% Overlap | 2+2 x 50% Overlap |
Bale Handling Equipment
Bale Handler
 |
Heavy duty tipping type bale handler for three point linkage, or attachment to High Lift Frame or Front End Loader. Unique bale retrieving hook attachment to pull down bales for feeding which had been stored on end. |
High Lift Frame.
 |
Multipurpose hoist- can be fitted with an assortment of implements- e.g. Bale Handler, Bale Spikes, Bale Splitter. Uses include stacking, loading and feeding bales of hay and silage. Ideal for dropping a bale into a circular feeder, or loading a trailer, etc. Various attachments can be switched in seconds. Highly versatile unit, can carry out many functions which would otherwise require a front loader. |
High Lift Frame Technical Data. |
|
| Load Capacity Max: | 1,000 kg |
| Ram Travel: | 106 cm |
| Overall Loading Height (approx.): | 1.5 m |
Bale Splitter.
 |
Another attachment for our highly successful High-Lift Frame System. This machine can pull the bale down from the stack, carry it to the feeding point , and cut it open - right down the centre - in less than 30 seconds. Easy to detach to allow High Lift Frame to be used for other purposes, e.g., loading, stacking, etc. Can cut bales of silage, hay or straw. Will operate on any tractor capable of carrying the bale. |
For more information on any of the machinery shown above contact Archway Products at Tel/Fax(078) 24753 or E-mail us at mcnameel@tinet.ie.